Jumpers

Password-override jumper (JMP1)  Here on the planar
The power-on password locks the keyboard and mouse (if attached to the mouse port) to help prevent unauthorized use of your server.  If you are using a mouse that is connected to the serial port, the mouse remains active. 
After you set a power-on password, Enter password appears each time you turn on the server.  Before you can use the server, you must enter the correct password.  (The password does not appear on the screen as you type it.)  When you enter the correct password, Password accepted appears on the screen, the keyboard and mouse are unlocked, and the system resumes normal operation.  If you type the wrong password, Incorrect password appears on the screen and Enter password is again displayed.  After three incorrect attempts, you must turn off the server and start again. 

Use the following procedures to bypass (erase) the power-on password.
 1. Power-off the system.
 2. Move the jumper so that it connects the center pin and the pin on the opposite end of the connector.
 3. Power-on the system.

The jumper does not need to be restored to its original position.  The password is removed each time the system is powered-on with the jumper in a new position.

Privileged-access password jumper (JMP2)   Here on planar
   Before setting an administrator (also known as privileged-access) password, it is a good idea to read this section in its entirety.  Using this security feature requires some planning and ongoing administration. 
   The administrator password allows you to control who has access to the system programs.  If an administrator password is set, you must enter it to use the system programs in the System Partition on the hard disk or on the Reference Diskette.  The administrator password also can be used to override the power-on password.  After an administrator password is set, only those who know the password can perform tasks such as: 
o Altering computer settings or features controlled by the system programs 
o Running diagnostic tests 
o Resetting the system after a forced entry (If the server is forced open, a POST error  occurs.  To clear the error, you must enter the administrator password. Read about the LogicLock

   Your server is shipped with the administrator password feature Disabled.  You must move a jumper on the system board before an administrator password can be set for the first time.  The jumper has two positions: 
o The locked state prevents an administrator password from being set, changed, or removed.  This is the position set at the factory. 
o The change state allows an administrator password to be set, changed, or removed. 

Warning: If an administrator password is set, then forgotten, it cannot be overridden or removed.  The system board must be replaced in order to access the system programs. 

 The privileged-access password jumper enables setting the privileged-access password.  The jumper has two positions, which are marked on the system board.  The system is shipped with this jumper in position 1, which prevents the privileged-access password from being set accidentally.  To set the password, move the jumper to position 0 then run Set Privileged-Access Password in the system utility programs. (The jumper position has no effect after the password is set.)
Note See Privileged-Access Password before attempting to set this password.
If the password is removed (using the system utility programs), the jumper can be returned to position 1 to prevent the password from being set.

     o To set the privileged-access password to the change state, move the jumper to position 0. 
     o To set the privileged-access password to the locked state, move the jumper to position 1. 
 

Cover Interlock Connector (JMP3)  Here on the planar
A 2- by 3-pin connector connects the cover-interlock switches to the controlling logic on the system board.  The two switches are connected to the tamper-evident logic.
   Switch 1 indicates the position of the keylock to the tamper-evident logic, and switch 2 indicates when the covers are off.
Pin Signal
1 Reserved
3 Switch 2
5 Switch 1
Pin Function
2 Reserved
4 Detect keylock position
6 Detect covers open 



Kickstart Jumper (JMP4)  Here on the planar
On the Server 95, serial port A can be used to power-on the system when the power supply is in the standby mode.  The kickstart jumper controls whether the 'serial data in' or the 'ring indicator' signals from serial port A are used to trigger the power-on sequence. When the jumper is in position 0, the 'serial data in' signal is logically connected to the input to the power supply; when the jumper is in position 1, the 'ring indicator' signal is the source.
  Note This jumper should be set to position 0 for serial connections that do not drive the 'ring indicator' signal, such as lease line and other directly-connected configurations.

KickStart Jumper Pin Description
PIN DESCRIPTION
1 Serial data in
2 Power on request output
3 Ring indicator 

 - To set power-on to leased-line state, move jumper to position 0. 
 - To set power-on to other modems state, move jumper to position 1.

   The Kickstart function is embedded in the Dallas DS1585S Serialized RTC next to the battery on the 95A planar.



Flash Memory Bank Selector (JMP5)
This jumper is on the processor complex and is used to select which bank of flash memory is accessed as ROM. The ROM subsystem consists of 256KB of flash memory in two banks of 128KB. If the jumper is in position 0 when the system is powered on, bank A is mapped to addresses hex 000E0000 to 000FFFFF and hex FFFE0000 to FFFFFFFF.  The system is shipped with the jumper in position 0 (bank A selected).

Access to ROM or RAM at address space hex 000E0000 to 000FFFFF is controlled by the bits in the memory controller registers. When ROM is enabled, it is not parity checked. 

If the jumper is in position 1, bank B is mapped to these addresses.


Note: Do not change the position of the jumper while the system is powered-on; unpredictable operation will occur.
Flash Memory Bank Select Jumper
PIN SIGNAL NAME POSITION
1 Open 1
2 Select bank B
3 Ground



Artifact
The "Flash ROM bank" switch -by the way- was originally planned for a sort of "emergency mode". Once you screwed up the Flash-BIOS you could toggle the bank, insert any working flash update in the FDD A: and restart the machine, which takes the flash-image from the floppy drive and recovers (as it can be done on the 704 in the "Bios recovery mode"). However: the base boot-BIOS did not have the required routines to delete the loused up bank of the Flash-ROM ... and as far as I know the loading of an image from Floppy does not work. Another useless feature.

Remote Maintenance Service Connector (JMP6)Here on planar
The system board provides a 2-by-2-pin Berg connector for a remote maintenance or service adapter, such as the IBM PS/2 ServerGuard adapter.  When the adapter is installed, the system can be turned off or reset from a remote location.
   When this adapter is not connected to this connector, a jumper must be in place that connects pins 1 and 2 together for the system to be powered-on.  These two pins provide a signal path to the 'power-on-request' signal to the power supply.

NOTE: If you get a 95 that's been stripped, they might have pulled the ServerGuard adapter out, and not jumpered JMP6. So if your new toy refuses to power up, check this jumper

Remote Maintenance Service Connector
PIN DESCRIPTION
1 Power on request input
2 Power on request output
3 -Reset
4 Not connected

Battery 3v Lithium
Duracell
Eveready
Panasonic Varta Sanyo Rayovac Maxell Toshiba
AWI
NEDA
Other
DL2032
ECR2032
CR2032
L14
5004LC
EA-2032C

PS/2 - 95xx Battery Life Expectancy/Voltage
   The battery used on the 95XX products has a normal life expectancy of five to seven years. The life of the battery is directly related to how the machine is used. Battery voltage is consumed only when the system is powered off. Since the battery is a lithium battery, it has very long shelf life. For correct machine operation the battery voltage should be between 2.5 volts and 3.7 volts.

To check the battery voltage:
- Turn off the system unit power.
- Remove the battery from the battery holder.
- Check the battery for a voltage of 2.5V - 3.7V DC
   If the battery voltage drops below 2.5 volts, it should be replaced with FRU P/N33F8354. (look at above chart)  After replacing the battery, the system unit should be powered on and checked for proper operation.

J1 on 90 Planar
1
(-) Power LED
2
(+) HD LED
3
(-) HD LED
4
(-) PWR 
5
(+) SPKR
6
(-) SPKR
7
(+) PWR
8
(+) Power LED

 
 

9595 Planar

9595 Main Page